How to Reset Roper Dishwasher

To reset a Roper Dishwasher, please follow these steps:

1. Turn off the dishwasher by pressing and holding the “Start/Resume” button for at least 3 seconds. The dishwasher will display “PF” (power failure) and shut down.
2. Unplug the dishwasher from the electrical outlet or switch off the circuit breaker to disconnect the power supply completely.
3. Wait for approximately 30 seconds to 1 minute to allow the dishwasher’s internal circuitry to drain any residual electrical charges.
4. Plug the dishwasher back into the electrical outlet or turn on the circuit breaker to restore power.
5. Press and hold the “Heated Dry” button for 5 seconds to reset the control lock feature if it was previously activated.
6. Close the dishwasher door and press the “Start/Resume” button to start a new wash cycle. The dishwasher should now function normally.

Reasons to Reset Your Roper Dishwasher

Resetting your Roper dishwasher is a helpful troubleshooting method when you encounter problems such as dishwasher not starting, improper cleaning, draining issues, or when specific error codes are displayed. At Settings King, a blog about technology settings, we understand how essential it is to maintain the optimal performance of your dishwasher. In some cases, reset dishwashers can help resolve minor issues and restore the normal operation of the appliance.

Common Error Codes

There are certain error codes that may indicate that a reset is necessary. These error codes include but are not limited to:

• F2 E2: The control board senses a key is stuck or shorted.
• F6 E4: Float switch open, indicating a water leak or overflow.
• F8 E1: Insufficient water supply or slow water filling.
• F9 E1: Long drain time detected.

If you encounter any of these error codes or experience any unusual behavior from your Roper dishwasher, a reset might be an effective way to fix the problem.

When to Reset

While resetting your Roper dishwasher may help in resolving minor issues, it is essential to know when to use this method. You should consider resetting the dishwasher when:

• You encounter error codes that are not resolved through other troubleshooting steps.
• Your dishwasher is not starting or is stuck in a specific cycle.
• The control panel is not responding or is not functioning correctly.

Troubleshooting Tips

If the reset process does not resolve the issues with your dishwasher, consider the following troubleshooting tips:

• Check the power supply and the electrical outlet to ensure they are functioning properly.
• Inspect the door latch for proper operation and alignment. A faulty door latch may prevent the dishwasher from starting.
• Ensure that there are no kinks or obstructions in the water supply and drain lines.
• Consult your dishwasher manual for specific error code resolutions and maintenance procedures.

If, after following these steps and troubleshooting tips, your dishwasher continues to experience issues, it may be best to consult a professional or contact Roper customer support for assistance.

FAQ Section

Here are some frequently asked questions and straightforward answers regarding the resetting of Roper dishwashers and troubleshooting relevant issues:

Can I reset my Roper dishwasher if it doesn’t display an error code?

Yes, you can reset your dishwasher even without an error code to resolve minor issues or to restart a wash cycle that may be stuck.

How do I know if my dishwasher needs a professional repair after resetting?

If, after resetting and troubleshooting your dishwasher, it still fails to operate correctly or displays persistent error codes, it’s likely time to consult a professional or contact Roper customer support for assistance.

Is it normal for my Roper dishwasher to display “PF” after the reset process?

Yes, “PF” (power failure) is a standard indication on Roper dishwashers when power is disconnected and reconnected during the reset process. It should disappear as you start a new wash cycle.

Will resetting the dishwasher erase the settings for delayed wash cycles?

Yes, resetting your dishwasher will typically reset any pre-programmed settings, including delayed wash cycles. You will need to re-enter these settings once the reset process is complete and the dishwasher is functioning normally.

How often should I reset my Roper dishwasher?

Resetting your dishwasher should only be done when you encounter specific issues or error codes, and other troubleshooting methods provided in the manual have proven unsuccessful. There is no need to reset your dishwasher regularly if it’s functioning well and not displaying any error codes.